![elexa tv wall mount elexa tv wall mount](https://i.ebayimg.com/images/g/XGYAAOSwHNVfMlEm/s-l300.jpg)
If you need to use the Extension Arms, you must use all Extension Arms in order for the Mount to properly hold your TV. If you have an oversized Flat Panel TV, you may need to use the Extension Arms provided. You will not use all of the hardware included. If you feel resistance, remove the bolt immediately and try another size! Next determine the correct length of the required bolt as described in the step 7. Thread the bolts carefully into your LCD or plasma by hand to determine which provided mount hardware (correct diameter) is appropriate for installation. Select bolts from Bags 1-4, which most resemble the holes in the back of your Flat Panel. Selecting the Appropriate Hardware for your Flat Panel.Drive the 2nd screw into the opposite upper right hand mounting hole of the Wall Plate, then proceed to drive the remaining 4 screws into the concrete anchors. Do not screw too tight until all the screws are in. Once the Wall Plate is in the correct position on the wall, screw 1 Dry Wall Screw and 1 Dry Wall Washer in the upper left mounting hole of the Wall Plate. Insert the anchors into the holes and set them flush to the wall by tapping them in with a hammer. Drill into the wall at least as deep as the screw is long (3 inches).
![elexa tv wall mount elexa tv wall mount](https://images-na.ssl-images-amazon.com/images/I/413ZA6eZT-L.jpg)
Drill holes for the concrete anchors using an electric drill with a masonry bit (1/2’’ or 12mm. Utilize the built-in bubble level to ensure proper mounting (Figure 3). Mark the six holes you will be using for concrete anchors (Figure 4).
#ELEXA TV WALL MOUNT INSTALL#
Place the Wall Plate at the height you want to install the Flat Panel wall Mount. NOTE: Due to the weight of the Flat Panel TV’s, it is necessary to mount the Wall Plate to at least 2 studs. Now tighten both screws, proceed to drive the remaining 2 screws into the studs. Using the Bubble Level as your guide, drive the 2nd screw into the opposite upper right hand mounting hole of the Wall Plate. Drill pilot hole with 1/8-inch drill bit. Do not screw too tight until after all the screws are in. Once the Wall Plate is in the correct position on the studs, screw 1 Hex Screw and 1 Hex Washer in the upper left mounting hole of the Wall Plate into the stud. The tilt arms will adjust horizontally to the right and left up to 8 inches after you determine the desired viewing location. The mount requires a minimum of two studs to ensure proper and safe installation. It is recommended that the center of the stud be used – and that a nail be used to verify that a stud has been located. Locate a proper place to mount by using a quality stud finder.
#ELEXA TV WALL MOUNT FULL#
Make sure all screws and bolts are tightened before allowing Wall Mount to bear the full weight of the LCD Display. DO NOT MOUNT ONLY TO DRYWALL.īefore installing, check to make sure all parts of the mount are included. THE MOUNT MUST BE ATTACHED TO WOOD STUDS OR TO PROPERLY INSTALLED ANCHORS IN CONCRETE. It is the responsibility of the installer to verify that the mount is anchored properly to the wall. Installer must make sure the Flat Panel Wall Mount is properly and securely attached and that appropriate fasteners are used. Please also visit our Web Site at for assistance. Our trained Customer Service Department is open 24 hours a day, 7 days a week, every day of the year and is prepared to assist you in both English and Spanish. IF YOU BELIEVE THIS MOUNT IS DEFECTIVE, HAS MISSING OR BROKEN PARTS, OR IF YOU ARE HAVING DIFFICULTY INSTALLING THIS MOUNT TO YOUR WALL OR FITTING YOUR TV, PLEASE CONTACT OUR COMPANY, LEVEL MOUNT, DIRECTLY.ĭial 1 8 or email us at any time of the day or night for a quick and efficient solution to your problem. Level Mount Large and Extra Large Fixed or Tilt TV Mounts InstructionsĭO NOT RETURN THIS PRODUCT TO THE STORE OR WEB SITE YOU PURCHASED FROM!
![elexa tv wall mount elexa tv wall mount](https://i.pinimg.com/originals/06/df/8c/06df8cc2cbbb8c945933cab17416a64a.jpg)
Level Mount Large and Extra Large Fixed or Tilt TV Mounts Gallery
![elexa tv wall mount elexa tv wall mount](https://i.ebayimg.com/thumbs/images/g/05QAAOSwt8NdU~q4/s-l225.jpg)
These arms allow for the TV to be positioned at multiple, secure, consistent angles across the TV by simply pivoting the TV to the desired viewing angle.ħ. The Tilt design incorporates our easy to use tilting arms. Low Profile Fixed or 15° Tilt Positions:.Level Mount Large and Extra Large Fixed or Tilt TV Mounts Features See Flash demo for product images and multimedia.